The Issue Whether Petitioner is entitled to additional credit for his solutions to four problems on the Principles and Practice of Engineering portion of the engineering licensure examination administered on October 30, 1998, by the National Council of Examiners for Engineers and Surveyors.
Findings Of Fact Based upon the evidence adduced at hearing and the record as a whole, the following findings of fact are made: On October 30, 1998, as part of his effort to obtain a Florida engineering license, Petitioner sat for the Principles and Practice of Engineering Examination (Examination). This is a national examination developed and administered by the National Council of Examiners for Engineers and Surveyors (NCEES). Petitioner chose to be tested in civil engineering. Petitioner received a raw score of 45 on the Examination. For the civil engineering specialization, a raw score of 45 converts to a score of 67. To pass the Examination, a converted score of 70 is needed. Petitioner formally requested (in writing, by letter dated March 26, 1999) that his solutions to Problems 120, 125, and 222 on the Examination be rescored. Petitioner's written request was made to Natalie Lowe of the Board, who forwarded it to the NCEES. Appended to Petitioner's letter to Ms. Lowe were two pages of "scratch paper" on which Petitioner had written during his post-examination review on March 19, 1999. On the first page were written comments he had made regarding the scoring of Problems 120 and 125. On the second page were the following written comments he had made regarding the scoring of Problems 220 and 222: 220 a, b, & c 2 parts b & c correct. Min. mark I should get[:] At least 5 instead of 2 and maybe 7. There is an error. 222 ok The NCEES's rescoring of Petitioner's solutions to Problems 120, 125, and 222 resulted in his receiving a raw score of 43 (or a converted score of 65, 5 points less than he needed to pass the Examination). The Board received the NCEES's rescoring results on May 12, 1999. The Board subsequently referred the matter to the Division to conduct an administrative hearing. At the administrative hearing that was held pursuant to the Board's referral, Petitioner challenged the grading of his solutions to Problems 120, 125, and 220 of the Examination, and indicated that he had "no dispute concerning the grading of [his solution to Problem] 222," notwithstanding that he had requested, in his March 26, 1999, letter to Ms. Lowe, that his solution to Problem 222 be rescored. Petitioner explained that he had made this request as a result of inadvertence and that he had actually intended to seek rescoring of his solution to Problem 220, not Problem 222. Problems 120, 125, and 222 were worth ten raw points each. Problem 120 contained four subparts (or requirements). Petitioner initially received four raw points for his solution to Problem 120. Rescoring did not result in any change to this score. Petitioner solved two subparts of Problem 120 correctly (subparts (a) and (b)). The solutions to the other two subparts of Problem 120 (subparts (c) and (d)), however, were incorrect inasmuch as Petitioner had neglected, in making the lateral force calculations and drawing the diagrams required by these subparts, to include the force attributable to the movement of the groundwater referred to in the problem. Therefore, in accordance with the requirements and guidelines of the NCEES scoring plan for this problem, the highest raw score that he could have received for his solution to this problem was a four, which is the score he received. Problem 125 contained three subparts (or requirements). Petitioner initially received a raw score of two for his solution to Problem 125. Upon rescoring, no change was made this raw score. Petitioner correctly solved only one of the three subparts of Problem 125 (subpart (c)). In his solution to subpart (a) of Problem 125, Petitioner did not provide, as required by this subpart, the quantities of water, cement, and aggregate necessary for the project described in the problem. Petitioner's solution to subpart (b) did not describe one of the acceptable slump increasing methods that the candidates were required describe in their solution to this subpart. Accordingly, giving Petitioner a raw score of two for his solution to Problem 125 was consistent with the requirements and guidelines of the NCEES scoring plan for this problem. Petitioner received a raw score of two for his solution to Problem 220. He did not request, in his March 26, 1999, letter to Ms. Lowe, a rescoring of his solution to this problem, and, as a result, his solution was not rescored. At the administrative hearing, Petitioner testified on his own behalf regarding the scoring of this solution and, during his testimony, contended that the score he received was too low; however, neither a copy of the problem, nor a copy of the NCEES scoring plan for this problem, was offered into evidence. Accordingly, the record is insufficient to support a finding that the score Petitioner received for his solution to Problem 220 was undeservedly low in light of the NCEES scoring plan for this problem. Petitioner initially received a raw score of eight for his solution to Problem 220. Rescoring resulted in this score being reduced two points to a six. Petitioner did not present any evidence supporting the position (which he advances in his Proposed Recommended Order) that he should have received a higher score for his solution to this problem, and, consequently, Respondent's expert, in his testimony at hearing, did not address the matter. While there were exhibits offered (by Respondent) and received into evidence relating to the scoring of Petitioner's solution to Problem 222, it is not apparent from a review of these exhibits that such scoring deviated from the requirements of the NCEES scoring plan for this problem (which was received into evidence as part of Respondent's Exhibit 12).
Recommendation Based on the foregoing Findings of Fact and Conclusions of Law, it is RECOMMENDED that a final order be entered rejecting Petitioner's challenge to the failing score he received from the NCEES on the Principles and Practice of Engineering portion of the October 30, 1998, engineering licensure examination. DONE AND ENTERED this 20th day of December, 1999, in Tallahassee, Leon County, Florida. STUART M. LERNER Administrative Law Judge Division of Administrative Hearings The DeSoto Building 1230 Apalachee Parkway Tallahassee, Florida 32399-3060 (850) 488-9675 SUNCOM 278-9675 Fax Filing (850) 921-6847 www.doah.state.fl.us Filed with the Clerk of the Division of Administrative Hearings this 20th day of December, 1999.
The Issue Whether Petitioner is entitled to additional credit for his responses to Question No. 130 of the Principles and Practice of Engineering portion of the engineering licensure examination administered on April 23, 1999, by the National Council of Examiners for Engineers and Surveyors.
Findings Of Fact Petitioner, Dennis Vann (Petitioner), is an applicant for licensure as a professional engineer in the State of Florida. On April 23, 1999, Petitioner sat for the Principles and Practice Engineering Examination portion of the engineer licensure examinations. This is a national examination developed, controlled, and administered by the National Council of Examiners for Engineering and Surveying (NCEES). Petitioner received a raw score of 45 on this examination. For the electrical engineering discipline, a raw score of 45 results in a converted score of 67. A minimum converted score of 70 is required to pass this examination. A raw score of 48 results in a converted score of 70. Therefore, Petitioner needs an additional 3 raw score points to earn a passing score on the examination. Petitioner challenged the scoring of Question No. 130 on the examination and formally requested the NCEES to rescore his solutions to the question. The NCEES rescored Question No. 130 and determined that Petitioner was not entitled to any additional points for Question No. 130. For Question No. 130, the maximum score achievable was Petitioner received a score of 4 on that item. The NCEES developed and used an Item Specific Scoring Plan (ISSP) for each examination question. Question No. 130 was scored by the NCEES according to the ISSP for that question. Question No. 130 contains two subparts, which require the examinee to address four discrete requirements. Petitioner correctly calculated the bus current (requirement 3). However, Petitioner failed to properly calculate the busway loading and determination of adequacy (requirement 1), the bus impedance (requirement 2), and percent voltage drop (requirement 4). Petitioner's response to Question No. 130 was initially assigned a score of 4. However, if graded correctly, that response would have resulted in a score of 6. The credible testimony of Respondent's expert was that under the ISSP for Question No. 130, Petitioner is entitled to a score of 6 for his response. With a score of 6 for Question No. 130, Petitioner's raw score is increased to 47. A raw score of 47 results in a converted score of 69. Even with the 2 additional points awarded to Petitioner's response to Question No. 130, his score on the professional engineering licensure examination is still below 70 and is not a passing score. Question No. 130 provides all the necessary information for an examinee to solve the problem. Moreover, Question No. 130 is properly designed to test an examinee's competence in electrical engineering.
Recommendation Based upon the foregoing Findings of Fact and Conclusions of Law, it is hereby RECOMMENDED that a final order be entered concluding that Petitioner is entitled to a score of 6 points for his response to Question No. 130, and recalculating Petitioner's total score on the examination on the basis of that conclusion. DONE AND ENTERED this 21st day of April, 2000, in Tallahassee, Leon County, Florida. CAROLYN S. HOLIFIELD Administrative Law Judge Division of Administrative Hearings The DeSoto Building 1230 Apalachee Parkway Tallahassee, Florida 32399-3060 (850) 488-9675 SUNCOM 278-9675 Fax Filing (850) 921-6847 www.doah.state.fl.us Filed with the Clerk of the Division of Administrative Hearings this 21st day of April, 2000. COPIES FURNISHED: Dennis Vann Post Office box 23054 Tampa, Florida 33623 William H. Hollimon, Esquire Ausley & McMullen 227 South Calhoun Street Post Office Box 391 Tallahassee, Florida 32301-1884 Dennis Barton, Executive Director Department of Business and Professional Regulation Board of Professional Engineers 1208 Hays Street Tallahassee, Florida 32301 Natalie A. Lowe, Esquire Florida Engineers Management Corporation 1208 Hays Street Tallahassee, Florida Barbara D. Auger, General Counsel Department of Business and Professional Regulation 1940 North Monroe Street Tallahassee, Florida 32399
The Issue The issue presented is whether Mr. Lord should be granted additional credit for his answer to question number 144 on the April 1990 Professional Engineer licensure examination.
Findings Of Fact Mr. Lord (Candidate #301402) received a score of 66.3 percent on the April 20, 1991, Principals and Practice portion of the Professional Engineer examination. A minimum passing score was 70.0 percent. Mr. Lord challenged the scoring of his response to question number 144. Question number 144 is an essay question involving an assembly line problem where four separate stations are used to assemble a product in sequence. A fifth station can assist in maximizing the number of finished products produced per hour, and is capable of performing all operations. The correct answer to question number 144 was 100 products per hour, while Mr. Lord's answer was 25 pieces per hour. Petitioner received a score of 2 (out of a possible 10) points on question number 144. This was based on the scoring plan developed for the exam by the National Council of Examiners for Engineering and Surveying. Mr. Lord used a method of averaging station assembly times to determine the maximum average number of products each station could produce. The averaging method gave a solution which did not identify the central issue presented by the essay question: identifying and eliminating the bottlenecks in production. Mr. Lord also made an assumption that the initial four stations could do all operations, thus defining the model inaccurately. This misreading allowed Mr. Lord to use an averaging methodology. Mr. Granata, the Department's expert, testified that it is a coincidence of the numbers that if you multiply Respondent's answer (25) by four (the initial number of machines) you get the Board's answer (100). Mr. Greenbaum, Petitioner's expert witness, testified that Petitioner's answer is "unique" and that he, as an expert, would have answered the question using a methodology similar to the one developed by the Department's expert, Mr. Granata, and by the NCEE (National Council of Examiners for Engineering).
Recommendation Based upon the foregoing Findings of Fact and Conclusions of Law, it is recommended that the challenge to the grading of Mr. Lord's response to question 144 on the April 1990 Professional Engineer licensure examination be dismissed. RECOMMENDED this 14th day of March, 1991, at Tallahassee, Florida. WILLIAM R. DORSEY, JR. Hearing Officer Division of Administrative Hearings The DeSoto Building 1230 Apalachee Parkway Tallahassee, Florida 32399-1550 (904) 488-9675 Filed with the Clerk of the Division of Administrative Hearings this 14th day of March, 1991. COPIES FURNISHED: William F. Whitson, Law Clerk Department of Professional Regulation 1940 North Monroe Street Tallahassee, Florida 32399-0792 Curtis Lord 1416A Old Lystra Road Chapel Hill, NC 27514 Rex Smith, Executive Director Department of Professional Regulation Board of Professional Engineers 1940 North Monroe Street Tallahassee, Florida 32399-0792 Jack McRay, General Counsel Department of Professional Regulation 1940 North Monroe Street Tallahassee, Florida 32399-0792
Findings Of Fact In October, 1973, the Petitioner filed an application for registration to practice architecture in the State of Florida with the Board. By letter dated November 21, 1973, the Board, through its Executive Secretary, denied the application stating that the Petitioner lacked the required degree (Petitioner's Exhibit 1). Petitioner requested that his experience be reviewed to determine whether he had training fully equivalent to such a degree (Petitioner's Exhibit 2). By letter dated August 19, 1974 the Board notified the Petitioner that his educational background was insufficient, and that the application would be denied. Petitioner thereupon filed a Declaratory Judgment Action in the Circuit Court of the Second Judicial Circuit, Leon County, Florida. The court adjudged that the Board was required to consider not only the Petitioner's educational training, but his private study, on-the-job training and other practical experience. A copy of the court's Final Declaratory Judgment was received in evidence as Hearing Officer's Exhibit 12. Petitioner again appeared before the Board and offered evidence respecting his training and practical experience. See: Petitioner's Exhibits 5 and 6, Hearing Officer's Exhibit 8. On June 11, 1976, the Board entered its order finding the Petitioner to be not qualified and denying the application (Hearing Officer's Exhibit 1). Petitioner thereupon requested a hearing in accordance with Florida Statutes Section 120.57(1). Petitioner's application for licensure is an administrative adjudicatory proceeding which commenced prior to January 1, 1975. The parties have nonetheless stipulated that the provisions of Section 120.57(1) will hereafter govern the proceeding. The Petitioner received a Bachelor of Science degree from Chicago Technical College, Chicago, Illinois on December 17, 1954. Petitioner's course of study was architectural engineering. The Chicago Technical College was not, during the time that Petitioner attended it, and is not now on the approved list of schools and colleges of architecture adopted and published by the Board. The course of study pursued by the Petitioner at Chicago Technical College was not the same as a program in architecture. The program was a highly technical engineering program. The design studio which is perhaps the major facet of an architectural program was not present in the architectural engineering program pursued by the Petitioner. Following his graduation the Petitioner worked with other architects in the general practice of architecture. His longest periods of employment were with Cabanban and Wasserman, architects, where he worked for four years and eleven months from 1958 until 1963; and with Ohrnstein and Wasserman, with whom he was employed for four years and four months from 1966 through 1971. In each of these jobs the Petitioner performed the sort of work ordinarily performed by architects. A listing of the different projects in which the Petitioner performed design and supervisory functions is set out as a part of Hearing Officer's Exhibit 10. A wide variety of commercial buildings, apartment complexes, and private residences are included. Petitioner served as a partner in Cabanban and Wasserman, and in Ohrnstein and Wasserman. Augustine Cabanban and Earl Ohrnstein were both registered architects during the course of the partnerships. Cabanban and Ohrnstein each testified that the Petitioner performed the full range of architectural services during the course of the partnerships, and that his work was excellent. Architectural drawings submitted by the Petitioner to the Board demonstrate that the Petitioner did not achieve a high level of design proficiency from his work experience. The best drawings submitted demonstrated a level of competence of approximately a third year architecture student in a five year program. Other drawings demonstrated a lack of design competence, and were inadequate. During 1972, the Petitioner passed the standard examination offered by the National Council of Architectural Registration Boards. Petitioner holds a current certificate issued by the National Council, and is registered to practice architecture in the State of Illinois. Schools or colleges of architecture approved by the Board have many common features, and the curricula offered at the schools are fairly consistent. Generally the programs and the curricula have remained consistent since approximately 1955 with minor variations, or changes of a technical sort. There is no real distinction between the sort of program which would have been approved in 1955, and the sort of program which would be approved today. Typically an approved program which operated on a quarter hour academic basis would require approximately 240 quarter hours for graduation. Approximately 75 quarter hours would be in architectural design culminating in a thesis. Approximately 60 quarter hours would be in general education subject matter, with between 30 to 35 hours in social science and humanities. The social science background is important because an architect must bring together all the factors which relate to the building environment, including social factors. The educational program followed by the Petitioner lacked the necessary design courses and social science courses which would be required in an approved architectural program. An architectural engineer is an engineer involved with buildings. The design courses in an architectural engineering program are set up to enable the engineer to work with an architect. Through on-the-job training the Petitioner received considerable design experience; however, drawings which he submitted to the Board did not evidence that he had achieved the level of design competence which would be required of a graduate of an approved architectural program. The fact that the Petitioner passed the National Council's test does not in itself establish that Petitioner reached the necessary level of competence. Petitioner did not offer evidence from which it could be concluded that his studies and experience would substitute for the social science background required of a graduate of an approved program. The Petitioner did not establish that he took social science courses, or engaged in individual study in the social sciences, or engaged in any other activities which would substitute for such an academic background.
The Issue The issues presented are: (1) whether or not Respondent wrongfully eliminated materials from the Candidate/Petitioner during the April 19, 1990 engineering examination, and if so, (2) whether the Candidate/Petitioner received a failing grade because the materials were wrongfully eliminated.
Findings Of Fact The Petitioner (#100021) received a score of 69.0 on the Professional Engineer Fundamentals Examination given April 19, 1990. A minimum passing score was 70.0 on the examination which is written by National Council of Engineering Examiners and graded by Education Testing Service. (Transcript Pages 36 and 39) Prior to the April 1990 examination, the Board sent each candidate a letter, dated December 18, 1989 (Exhibit P-1) (Transcript Page 9 and 12), which said, "No review publications directed principally toward sample questions and their solutions of engineering problems are permitted in the examination room." (Transcript Page 31). The candidates were also provided with a "Candidate Information Booklet" dated January 1990 (Exhibit R-1, Transcript Page 77). The booklet states on page 14, "No books with contents directed toward sample questions or solutions of engineering problems are permitted in the examination room." (Transcript Pages 77 and 96). Petitioner, who also took the October 1989 examination had received notice at that examination that the Board of Engineers intended to change the procedure allowing reference materials in the examination. (Transcript Page 89 and Respondent's Exhibit 2.) The Board of Professional Engineers advised the examination supervisor and proctors that no engineering "review" materials would be allowed in the examination although engineering "reference" materials could be brought into and used for the examination. However the books which were excluded included books without "review" in the title, books with "reference" in the title, and books which contained problems and solutions. Before the examination began Deena Clark, an examination supervisor, read over a loud speaker system names of books that would not be permitted (Transcript Page 81). Practice examination and solution manuals were not allowed for use by engineering candidates (Transcript Pages 93 and 94). Schram's outlines and other materials were also excluded (Transcript Page 91). Also excluded was Lindeburg's 6th edition, "Engineering In Training Review Manual." (Transcript Pages 16 and 79). This decision was verified by the Board before the examination began (Transcript Page 81). After the examination had begun, Ms. Clark announced that the candidates could put certain copyrighted materials in a three-ring binder and use them which had been excluded earlier (Transcript Page 85). This was in response to candidates who needed economics tables for the examination However, no time was provided the candidate to prepare these references and only one minute was added to the examination time. (Transcript Page 85). Petitioner did not bring any economic tables to the examination site except those contained in books which were not allowed in the examination. (Transcript Page 19). Petitioner did not remove the economic tables and permitted references from the Lindeburg's review manual until lunch and these tables were not available to him on the morning examination. (Transcript Pages 22 and 88). Of the six engineering economics questions on the morning portion for the examination, the candidate correctly answered four. No data was provided on the nature of these questions. The Candidate correctly answered 53 questions in the morning (weighted x 1) and 23 questions in the afternoon (weighted x 2) for a total of 99 weighted required points. He answered eight questions correctly in the "addition" portion of the examination. The table for eight additional questions correct in the "Scoring Information Booklet" used in determining the candidates final grade shows the adjusted equated score was 126 and his scaled score was 69. (Page 21 of booklet). The value of each economics question converted to final scoring scale was enough that passage of one economics question would have resulted in passage of the examination. The exclusion of certain materials from the examination was arbitrary and capricious and was done by a few individuals without any stated objective standard published by the board. Further, the board knew before the examination which books were to be excluded and could have notified examinees of the exact items to be excluded. The Board's generally poor handling of this matter is exemplified in announcing after the examination had begun that items previously excluded could be used if placed in a ring binder but not allowing any time to prepare such materials. (Tx. pgs., 74-80, 84-86, and 91-97) The Petitioner would have used several tables which were excluded if the announcement had been made before the morning examination began with time to put the items in acceptable form. After notifications in October 1989, December 1989, and January 1990, Petition admitted that he did not call the Board of Professional Engineers to ask for guidance on books that would not be allowed on the April 1990 examination (Transcript Page 29). However, a final decision on books to be excluded was not made until approximately two weeks before the examination. The Petitioner did not show that the two questions which he missed on the Engineering Economics portion of the morning examination were missed for lack of the tables. The examination is a national examination and there is no evidence that the requirements and limits established by the Board in Florida were applicable nationwide. To alter the national instructions locally potentially adversely affects Florida results.
Recommendation Based upon the foregoing findings of fact and conclusions of law, it is recommended that the Petitioner be permitted to take the examination without charge on one occasion. RECOMMENDED this 27th day of March, 1991, in Tallahassee, Florida. STEPHEN F. DEAN Hearing Officer Division of Administrative Hearings The DeSoto Building 1230 Apalachee Parkway Tallahassee, FL 32399-1550 (904) 488-9675 Filed with the Clerk of the Division of Administrative Hearings this 27th day of March, 1991. 1/ The general information provided to examinees by the State Board regarding the values of questions on the examination and scoring it misleading or inaccurate because neither the weighted required score nor the adjusted score was 48% of 80, 280, or any other number related to the scaled score of 70. The manner in which these values are associated with the scale score of 70 is contrary to the Board's explanation and is not self evident. This is a potential problem if the matter were formally challenged, and it appears the Board needs to reassess its procedures and instructions. APPENDIX TO RECOMMENDED ORDER, CASE NO. 90-5728 The Petitioner did not submit proposed findings. The Respondent submitted proposed findings which were read and considered. The following proposed findings were adopted or reject for the reasons stated: Adopted. Issue not fact. - 4. Rejected. Preliminary statement not fact. 5. -12. Adopted. Rejected. Preliminary statement not fact. Rejected as irrelevant. Rejected as preliminary statement. Adopted. Adopted. COPIES FURNISHED: Alan K. Garman Civil-Tech, Inc. 3573 Commercial Way Street B Spring Hill, FL 34606 William F. Whitson, Law Clerk Department of Professional Regulation 1940 North Monroe Street Tallahassee, FL 32399-0792 Rex Smith Executive Director Board of Professional Engineers Department of Professional Regulation 1940 North Monroe Street Tallahassee, FL 32399-0792 Jack McRay, General Counsel Department of Professional Regulation 1940 North Monroe Street Tallahassee, FL 32399-0792
The Issue The issue presented for decision herein is whether or not the Petitioner successfully completed the answers posed on the April, 1987 professional engineer's examination.
Findings Of Fact Petitioner took the April, 1987 professional engineering examination and was advised that he failed the principles and practice portion of the examine. His raw score was 45 points and the parties stipulated that he needed a minimum raw score of 48 points to pass the examination. In his request for hearing, Petitioner challenged questions 120, 123 and 420. However, during the hearing, he only presented testimony and challenged question 420. Question 420 is worth 10 points and is set forth in its entirety in Petitioner's Exhibit Number 1. For reasons of test security, the exhibit has been sealed. Question 420 requires the examinee to explore the area regarding "braced excavations" and explores the principles involved in such excavations. Question 420 requires the examinee to calculate the safety factor for a braced excavation including the depth of excavation which would cause failure by "bottom heaving". Petitioner, in calculating the safety factor, made a mathematical error when he incorporated the B-prime value calculation which was inserted into the equation in making his calculations. Question 420 does not direct the applicant to apply the calculations to either a square excavation or to a rectangular excavation. Petitioner assumed the shape of the excavation to be square and calculated the factor of safety according to that assumption. In assuming the square excavation, Petitioner did not make the more conservative calculation that will be required in making the safety factor calculation for a rectangular excavation. In this regard, an examination of Petitioner's work sheet indicates that he referenced the correct calculation on his work sheet but the calculation was not transferred to or utilized in the equation. Respondent utilizes the standard scoring plan outline, which is more commonly known as the Items Specific Scoring Plan (ISSP) which is used by the scorers in grading the exam. The ISSP provides a scoring breakdown for each question so that certain uniform criteria are met by all applicants. For example, four points are given for a correct solution on a specific question regardless of the scorer. This criteria is supplied by the person or persons who prepared the exam. The criteria indicates "in problem-specific terms, the types of deficiencies that would lead to scoring at each of the eleven (0-10) points on the scale". The ISSP awards six points on question 420 when the applicants meets the following standards: "all categories satisfied, applicant demonstrate minimally adequate knowledge in all relevant aspect of the item." ISSP awards seven points on question 420 when the applicant's answer meets the following standard: "all categories satisfied, obtains solution, but chooses less than optimum approach. Solution is awkward but reasonable". The ISSP awards eight points on question 420 when the applicant's answer meets the following standards: "all categories satisfied. Errors attributable to misread tables or calculating devices. Errors would be corrected by routine checking. Results reasonable, though not correct". The ISSP awards nine points on question 420 when the applicant's answer meets the following standard: "all categories satisfied, correct solution but excessively conservative in choice of working values; or presentation lacking in completeness of equations, diagrams, orderly steps in solution, etc." The ISSP criteria for awarding nine points as to question 420 clearly requires that the Petitioner calculate the correct solution without mathematical errors. The Petitioner's answer was not correct regardless of the assumption as to the shape of the excavation since he made a mathematical error. The ISSP criteria for awarding eight points as to question 420 allows Petitioner to calculate the answer with mathematical errors with the requirements that the results are reasonable. Petitioner made a mathematical error although his result was reasonable. His answer fits the criteria for the award of eight points in conformity with the ISSP criteria. Petitioner received six points for his answer to question 420 whereas he is entitled to an award of eight points.
Recommendation Based on the foregoing Findings of Fact and Conclusions of Law, it is RECOMMENDED that: Respondent enter a Final Order determining that Petitioner failed the principles and practice portion of the April, 1987 engineering examination. RECOMMENDED this 30th day of June 1988, in Tallahassee, Florida. JAMES E. BRADWELL Hearing Officer Division of Administrative Hearings The Oakland Building 2009 Apalachee Parkway Tallahassee, Florida 32301 (904) 488-9675 Filed with the Clerk of the Division of Administrative Hearings this 30th day of June, 1988. COPIES FURNISHED: Glen E. Wichinsky, Esquire 900 Glades Road, 5th Floor Boca Raton, Florida 33431 Michael A. Mone', Esquire Department of Professional Regulation 130 North Monroe Street Tallahassee, Florida 32399-0750 Allen R. Smith, Jr. Executive Director Department of Professional Regulation, Board of Professional Engineers 130 North Monroe Street Tallahassee, Florida 32399-0750 William O'Neil, Esquire General Counsel Department of Professional Regulation 130 North Monroe Street Tallahassee, Florida 32399-0750
The Issue The issue to be resolved is whether Petitioner is entitled to additional credit for her response to question nos. 122 and 222 of the civil engineering examination administered on October 31, 1997.
Findings Of Fact On October 31, 1997, Petitioner took the civil professional engineering licensing examination. A score of 70 is required to pass the test. Petitioner obtained a score of 69. Petitioner challenged the scoring of question nos. 122 and 222. As part of the examination challenge process, Petitioner's examination was returned to the National Council of Examiners for Engineering and Surveying where it was re-scored. In the re-score process, the grader deducted points from Petitioner's original score. Petitioner was given the same raw score of 6 on question number 122; however, on question number 222 her raw score of 4 was reduced to a 2. Petitioner needed a raw score of 48 in order to achieve a passing score of 70; she needed at least three additional raw score points to obtain a passing raw score of 48. Petitioner is entitled to a score of 6 on problem number 122. The solution and scoring plan for that problem required the candidate to obtain a culvert size in the range of 21-36 inches. The Petitioner incorrectly answered 3.1 feet or 37.2 inches. She is not entitled to additional credit for problem number 122 because she answered the question with the wrong size culvert. Problem number 122 required the candidate to use a predevelopment peak flow of 40 cubic feet per second (cfs). Petitioner used 58.33 cfs. She chose the maximum flow rather than the predevelopment peak flow. In solving problem number 122, Petitioner chose a design headwater depth of 4.8 feet. The correct solution required a design headwater depth of 5.7 feet. Petitioner made another mistake in problem number 122; she failed to check the water depth in the downstream swale. Petitioner concedes she was given sufficient information to solve problem number 122. She understood what the question was asking of her. She admits that she did not compute the critical depth of the water and that she did not complete the solution. Question number 222 had three parts. The candidate was required to determine the footing size, to select the reinforcing steel, and to provide a sketch for a concrete column located along the edge of a building. Petitioner understood the question and was provided enough information to solve the problem. Petitioner correctly checked the footing size as required by the first part; however, she did not select the reinforcing steel or show the required sketch. Therefore, Petitioner did not complete enough of the problem to qualify for a score of 4 points. She is entitled to a score of 2 points. The examination questions at issue here were properly designed to test the candidate's competency in solving typical problems in real life. The grader (re-scorer) utilized the scoring plan correctly. Petitioner has been in the United States for approximately eleven years. She lived in Romania before she came to the United States. In Romania, Petitioner used only the metric system in her professional work. While she has used the English system since moving to the United States, Petitioner is more familiar with the metric system. The Principles and Practice examination is an open-book examination. Petitioner took a book entitled the Fundamentals of Engineering Reference Handbook to the examination. When the proctor examined her books, she told the Petitioner she was not permitted to keep the handbook. The proctor took the handbook from the Petitioner. Petitioner protested the confiscation of her reference book because she had used the same book in two previous tests. About ten minutes later, the proctor's supervisor returned the book to Petitioner. Petitioner's book was returned at least ten minutes before the test began. She was permitted to use the book during the test. There is no persuasive evidence that the proctor's mistake in temporarily removing Petitioner's reference book caused her to be so upset that she failed the test. Candidates were not permitted to study their books prior to the beginning of the examination. Petitioner may have been nervous when the test began. However, Petitioner received a perfect score of ten points on the first problem she worked, problem number 121.
Recommendation Based upon the findings of fact and conclusions of law, it is RECOMMENDED that the Board of Professional Engineers enter a Final Order confirming Petitioner's score on the examination and dismissing the Petitioner's challenge. DONE AND ENTERED this 13th day of January, 1999, in Tallahassee, Leon County, Florida. SUZANNE F. HOOD Administrative Law Judge Division of Administrative Hearings The DeSoto Building 1230 Apalachee Parkway Tallahassee, Florida 32399-3060 (850) 488-9675 SUNCOM 278-9675 Fax Filing (850) 921-6847 www.doah.state.fl.us Filed with the Clerk of the Division of Administrative Hearings this 13th day of January, 1999. COPIES FURNISHED: Natalie A. Lowe, Esquire Board of Professional Engineers 1208 Hays Street Tallahassee, Florida 32301 William Bruce Muench, Esquire 438 East Monroe Street Jacksonville, Florida 32202 Lynda L. Goodgame, General Counsel Department of Business and Professional Regulation 1940 North Monroe Street Tallahassee, Florida 32399-0792 Dennis Bartin, President Florida Engineers Management Corporation 1940 North Monroe Street Tallahassee, Florida 32399-0792
The Issue The issue in this case is whether the Petitioner's academic record meets the academic requirements that are prerequisites to taking the Fundamentals of Engineering examination.
Findings Of Fact The Petitioner submitted an application for approval to take the Fundamentals of Engineering examination. The Petitioner studied engineering at the Tongji University in the People's Republic of China from 1991 to 1995. He majored in Building Engineering and was awarded the degree of Bachelor of Engineering on July 10, 1995. Beginning in September of 1995, the Petitioner studied engineering at the graduate level at Tongji University. His graduate studies lasted until April of 1998, at which time he was awarded the degree of Master of Engineering with a major in Structural Engineering. During the course of his graduate studies at Tongji University from September of 1995 until April of 1998, the Petitioner completed a total of 38 semester credit hours. Those semester credit hours included the following courses with their indicated semester credit hours: Applied Statistics 2 credit hours Numerical Analysis 3 credit hours The courses titled Applied Statistics and Numerical Analysis are both higher mathematics courses. In the fall of 2000, the Petitioner began further graduate studies in engineering at Auburn University. He studied at Auburn University through the spring of 2002. The courses taken by the Petitioner at Auburn University included the following, with the indicated number of semester credit hours: Advanced Structural Analysis 3 credit hours Advanced Stress Analysis 3 credit hours Structural Dynamics I 3 credit hours Finite Element Methods in Structural Mechanics 3 credit hours The course titled Finite Element Methods in Structural Mechanics is a higher mathematics class. The other three Auburn courses listed immediately above, if not pure mathematics courses, are certainly courses which involve the application of advanced principles of mathematics. To successfully complete such courses, a person would have to be well-grounded in higher mathematics. In the fall of 2002, the Petitioner transferred to the University of Florida where he continued his graduate studies in engineering. On December 20, 2003, the University of Florida awarded the Petitioner the degree of Master of Engineering with a major in Civil Engineering. Pursuant to Florida Administrative Code Rule 61G15- 20.007 the Petitioner submitted his educational credentials to an educational evaluator approved by the Board. The evaluator selected by the Petitioner was Josef Silny & Associates, Inc. (Silny). Following its evaluation of the Petitioner's educational credentials, Silny prepared a Report of Evaluation of Educational Credentials (Silny Report) dated June 15, 2005. The Silny Report reached the conclusion that the Petitioner's undergraduate education at Tongji University was not the equivalent of a degree in engineering earned from a program approved by ABET. Silny was of the view that the Petitioner's undergraduate course of study at Tongji University was not equivalent because his curriculum was deficient five semester credit hours in higher mathematics and basic sciences and was deficient one semester credit hour in humanities and social sciences.1 The conclusions reached in the Silny Report were based on an evaluation of the Petitioner's undergraduate course work at Tongji University from 1991 to 1995. The Silny Report did not take into consideration any of the courses taken by the Petitioner during his graduate studies at Tongji University from 1995 to 1998, during his graduate studies at Auburn University from 2000 to 2002, or during his graduate studies at the University of Florida from 2002 to 2003. During his undergraduate engineering studies at Tongji University, the Petitioner completed 36 semester hour credits of course work in the areas of higher mathematics and basic sciences. Silny is of the opinion that semester credit hours completed at Tongji University represent less study than semester credit hours completed at an accredited engineering school in a university in the United States of America. Specifically, Silny is of the opinion that semester credit hours completed at Tongji University are the equivalent of only 75 percent of semester credit hours earned in accredited engineering programs in the United States of America. Accordingly, when Silny evaluated the Petitioner's undergraduate education credentials, Silny multiplied the 36 semester credit hours the Petitioner had completed at Tongji University in the areas of higher mathematics and basic sciences by a factor of 0.75, and concluded that those 36 semester credit hours were equivalent to only 27 semester credit hours at an accredited engineering program in the United States of America.2 Florida Administrative Code Rule 61G15-20.007 includes the following requirements regarding applicants with degrees from foreign institutions: Applicants having degrees from foreign institutions shall be required to document “substantial equivalency” to the 2002 ABET Accreditation Yearbook for Accreditation Cycle Ended September 30, 2002 engineering criteria. This document is hereby incorporated by reference. In order to document “substantial equivalency” to an ABET accredited engineering program, the applicant must demonstrate: 32 college credit hours of higher mathematics and basic sciences. The hours of mathematics must be beyond algebra and trigonometry and must emphasize mathematical concepts and principles rather than computation. Courses in probability and statistics, differential calculus, integral calculus, and differential equations are required. Additional courses may include linear algebra, numerical analysis, and advanced calculus. As for the hours in basic sciences, courses in general chemistry and calculus-based general physics are required, with at least a two semester (or equivalent) sequence of study in either area. Additional basic sciences courses may include life sciences (biology), earth sciences (geology), and advanced chemistry or physics. Computer skills and/or programming courses cannot be used to satisfy mathematics or basic science requirements. 16 college credit hours in humanities and social sciences. Examples of traditional courses in this area are philosophy, religion, history, literature, fine arts, sociology, psychology, political science, anthropology, economics, and no more than 6 credit hours of languages other than English or other than the applicant’s native language. Courses in technology and human affairs, history of technology, professional ethics and social responsibility are also acceptable. Courses such as accounting, industrial management, finance, personnel administration, engineering economics and military training are not acceptable. Courses which instill cultural values are acceptable, while routine exercises of personal craft are not. 48 college credit hours of engineering science and engineering design. Courses in this area have their roots in mathematics and basic sciences but carry knowledge further toward creative application. Examples of traditional engineering science courses are mechanics, thermodynamics, electrical and electronic circuits, materials science, transport phenomena, and computer science (other than computer programming skills). Courses in engineering design stress the establishment of objectives and criteria, synthesis, analysis, construction, testing, and evaluation. In order to promote breadth, at least one engineering course outside the major disciplinary area is required. In addition, evidence of attainment of appropriate laboratory experience, competency in English, and understanding of the ethical, social, economic and safety considerations of engineering practice must be presented. As for competency in English, transcripts of course work completed, course content syllabi, testimonials from employers, college level advanced placement tests, Test of English as a Foreign Language (TOEFL) scores of at least 550 in the paper- based version, or 213 in the computer-based version, will be accepted as satisfactory evidence.
Recommendation On the basis of the foregoing findings of fact and conclusions of law, it is RECOMMENDED that a Final Order be issued concluding that the Petitioner has met the requirements of Florida Administrative Code Rule 61G15-20.007, and is eligible to take the Fundamentals of Engineering examination. DONE AND ENTERED this 29th day of March, 2006, in Tallahassee, Leon County, Florida. S MICHAEL M. PARRISH Administrative Law Judge Division of Administrative Hearings The DeSoto Building 1230 Apalachee Parkway Tallahassee, Florida 32399-3060 (850) 488-9675 SUNCOM 278-9675 Fax Filing (850) 921-6847 www.doah.state.fl.us Filed with the Clerk of the Division of Administrative Hearings this 29th day of March, 2006.
The Issue The issue for consideration in this case is whether Petitioner, Andrew Netupsky, should be granted licensure by endorsement as a professional engineer in Florida.
Findings Of Fact At all times, pertinent to the issues herein, Respondent, Florida Engineers Management Corporation (FEMC), was the state agency responsible for the licensing of professional engineers and for the regulation of the engineering profession in Florida. Petitioner, Andrew Netupsky, is a professional engineer licensed in the Province of British Columbia, Canada. He graduated from the University of British Columbia in 1971 with a Bachelor of Applied Science in Civil Engineering and was licensed as a Registered Professional Engineer (Structural) in British Columbia in 1973. He was subsequently licensed by endorsement as a Registered Professional Engineer (Structural) in Arizona in 1987. The State of Arizona accepted Petitioner's scholastic examinations as a valid basis for licensure. The State of Florida does not. Petitioner's engineering education in Canada was accredited by the Canadian Counsel of Professional Engineers (CCPE). The accrediting body within the United States is the Engineering Accreditation Commission of the Accreditation Board for Engineering and Technology (EAC/ABET). By virtue of a mutual agreement between the accrediting bodies in the United States and Canada, Petitioner's Canadian schooling and accreditation is deemed equivalent to an EAC/ABET accredited engineering program. Accreditation and schooling are not at issue in this proceeding. Sometime before November 15, 1999, Petitioner applied to the Florida Board of Professional Engineers (Board) for licensure by endorsement as a professional engineer in Florida. By letter dated November 22, 1999, the Board notified Petitioner that his application had been deemed administratively complete and that it would be presented for review to the Board's Application Review Committee (Committee) on December 7, 1999. Though the educational programs in Canada and Florida are similar, the methods and requirements for licensure are not. In Canada, a successful graduate of an engineering program does not take a subsequent comprehensive examination as a condition of licensure. Canadian engineering graduates are permitted to practice upon graduation from an engineering course of study. After the graduate has obtained four years of acceptable engineering experience, he or she takes a Principles and Practices examination which is, in effect, an examination on the laws and rules of practice. The subject matter examinations taken by the candidate while in engineering school serve as the required technical examination. In Florida, candidates for licensure as a Professional Engineer take two examinations in addition to the course material examinations given in engineering school. One of these is the Fundamentals examination, also known as the Engineer In Training/EIT examination. It is an examination of the candidate's broad knowledge of mathematics, general sciences, and engineering sciences. This examination is generally taken shortly before or upon graduation from a baccalaureate program in engineering school. Upon successful practice of that examination, and upon four years of acceptable engineering experience, the candidate may sit for the Principles and Practice examination, also known as the Professional Engineer or PE examination. This latter examination tests the candidate's knowledge in a specific discipline. Both the Fundamentals examination and the Principles and Practice examination are prepared and provided to the states by the National Council of Examiners for Engineers and Surveyors (NCEES). Petitioner took the examinations required for each of the mathematics, general science, and engineering courses required by his course of study as an engineering student in Canada, a total of 25 separate course examinations. In 1973 he also took the Professional Practice examination administered by the Association of Professional Engineers and Geo-scientists of British Columbia (APEGBC). At no time did he take either examination prepared by NCEES. Petitioner contends the course examinations he took in engineering school and the Professional Practice examination he took after graduation are equivalent to the NCEES examination process administered to candidates for licensing as professional engineers in Florida, and that he should be licensed by endorsement as a professional engineer in this state. In support of Petitioner's contention, he presented the testimony of Dr. Leslie Tremaine Russell, of Halifax, Nova Scotia, a mechanical engineer in practice since 1955, and past chairman of the Canadian Council of Professional Engineers (CCPE) and the Canadian Engineering Accreditation Board (CEAB). Dr. Russell has worked as a design engineer and has served as a university professor of engineering, being designated as Professor Emeritus for the past nine years. He has reviewed the engineering education programs in all Canadian provinces except Nova Scotia, Quebec, and Saskatchewan, and works in harmony with the ABET, the American equivalent to the CEAB to ensure that the engineering education programs in the two countries are as similar as is possible. As in the United States, the CCPE gains all its powers from the various provincial licensing bodies. All provinces require graduation from an accredited engineering program, and accreditation of the programs is done at the request of the university presenting the program. All students who seek to graduate from an accredited engineering program in Canada must meet all requirements of the accrediting board. Before a candidate may be licensed as an engineer in Canada, he or she must both be a graduate of an accredited engineering program and have four years' experience in the practice of engineering. The CEAB monitors engineering programs at all Canadian engineering schools to ensure that the programs are adequate to guarantee uniformity and safety. If so, the graduates are not required to take other comprehensive examinations. The engineering department at the University of British Columbia has been accredited since 1965. While the Canadian and United States programs are similar, Dr. Russell concedes that similar is not identical. An international agreement forged under the North American Free Trade Act in 1995, and applying to engineering education and licensing in Canada, the United States, and Mexico, calls for reciprocal accreditation of individuals with a four- year degree from an accredited institution and eight years of satisfactory experience. This agreement was signed by NCEES, ABET, and NSPE in the United States, but it requires ratification by the individual licensing bodies in order to become effective. The agreement has been ratified by all provinces in Canada, but only by Texas in the United States. Dr. Russell, in his many years of experience, has taken both eight-hour examinations, such as the NCEES examinations, and shorter ones as well. He is not convinced that the NCEES examinations, being made up of true/false and multiple choice questions, are particularly reflective of a candidate's actual knowledge. They are somewhat superficial. On the other hand, a university examination requires a full issue analysis. Dr. Russell is comfortable with the conclusions that the Canadian university subject examinations, which Petitioner took while in engineering school, are the equivalent of the NCEES examination on the same subject matter. Dr. Melvin W. Anderson, currently Dean of the College of Engineering at the University of South Florida, also reviewed the examinations presented by Petitioner and agreed that many had questions that were typical of the questions asked on final examinations in university engineering courses. However, some of those courses claimed by Petitioner to be fundamentals of engineering courses, such as those in English, Russian, Surveying, and Biology, have little to do with engineering science and are not subjects covered by the NCEES Fundamentals examination. Dr. Anderson also opined that the university examinations taken by Petitioner cannot be considered equal to the NCEES examinations. Further, according to Dr. Anderson, the NCEES examinations are developed by a panel of experts and administered nation-wide by state licensing bodies. The Fundamentals portion of the examination is taken by university seniors or graduates and deal with engineering and fundamental science and mathematics. The Principles and Practice examination is administered after four years of practice and deals with problem solving. Scores on the NCEES examinations are based on national assessment by practicing engineers who establish a cut score which is based on the assessed difficulty of the examination. The cut score is then equated to a passing score. When the examination is taken, it is "blind graded" which avoids any potential for the grader to be influenced by knowledge of the examinee. While the quality of engineering education in Canada has been shown to be the equivalent of that in the United States, and while the licensing process in Canada has been shown to be comprehensive and effective, the differences in the systems, in particularity the requirement for a comprehensive examination as required in the United States, render the systems different and not equivalent.
Recommendation Based on the foregoing Findings of Fact and Conclusions of Law, it is recommended that the Board of Professional Engineers enter a Final Order denying Petitioner's application for licensure by endorsement as a professional engineer in Florida. DONE AND ENTERED this 4th day of October, 2000, in Tallahassee, Leon County, Florida. ARNOLD H. POLLOCK Administrative Law Judge Division of Administrative Hearings The DeSoto Building 1230 Apalachee Parkway Tallahassee, Florida 32399-3060 (850) 488-9675 SUNCOM 278-9675 Fax Filing (850) 921-6947 www.doah.state.fl.us Filed with the Clerk of the Division of Administrative Hearings this 4th day of October, 2000. COPIES FURNISHED: Andrew Netupsky 1275 West 75th Avenue Vancouver, British Columbia Canada V6P 3G4 Edwin A. Bayo, Esquire Office of the Attorney General Department of Legal Affairs The Capitol, Plaza Level-01 Tallahassee, Florida 32399-1050 Dennis Barton, Executive Director Board of Professional Engineers Florida Engineers Management Corporation 1208 Hays Street Tallahassee, Florida 32301 Natalie A. Lowe, Esquire Florida Engineers Management Corporation 1208 Hays Street Tallahassee, Florida 32802-1900 Barbara D. Auger, General Counsel Department of Business and Professional Regulation Northwood Centre 1940 North Monroe Street Tallahassee, Florida 32399-0792
